Search results

like the title says i need 28 spline posi carrier or complete third member not concern what ratio i just need theposi i don't need a spool let me know what yuou guys have thanks jeremy

looking for rearend for a metric car would like complete rearend but let me know what you have doesnt have to be for metric i can fab the mounts message or call 314-808-1061

looking for rearend for a metric car would like complete rearend but let me know what you have doesnt have to be for metric i can fab the mounts message or call 314-808-1061

i have a set of 215 64cc pro 1 they have port work done with the intake runners and chambers they have 1.55 solid roller springs good to .750 lift titanium retainers and 10 degree locks 7/16 studs and guide plates. 20 runs and a few street miles since freshen up. also comes with hardland sharp...

here is a link to racingjunk for pics http:/i have a set of 215 64cc pro 1 they have port work done with the intake runners and chambers they have 1.55 solid roller springs good to .750 lift titanium retainers and 10 degree locks 7/16 studs and guide plates. 20 runs and a few street miles since...

i have a set of 215 64cc pro 1 they have port work done with the intake runners and chambers they have 1.55 solid roller springs good to .750 lift titanium retainers and 10 degree locks 7/16 studs and guide plates. 20 runs and a few street miles since freshen up. also comes with hardland sharp...

i have a whole 355 forged internals allinum heads intake roller cam lifters and block callies stealth crank new $1400.00 asking $400 wiseco pro pistons 12.5 comp ratio made for nitrous part # k401b3 new $650 asking $450 childs alkerly pro extreme rings new $190 asking $100 eagle 6" h beam rods...

i have a nice set of rhs toproline cast iron heads for sbc 220 intake runners 72cc chambers 2.02 and 1.60 new valves 1.55 roller springs with retainers and 10 degree locks heads have been mild port and polish also had new valve job done left apart so people can inspect them also in the package...

i have a set of protopline 72cc 220 cc intake runner cast iron heads with 2.02 & 1.60 valves these heads are very good performing heads they made 600 hp on a pump gas 434 and 500 hp on a pump gas 383 they have comp cams 1.55 roller springs and comp cams stud girdles missing a couple of poly...

i have a set of protopline 72cc 220 cc intake runner cast iron heads with 2.02 & 1.60 valves these heads are very good performing heads they made 600 hp on a pump gas 434 and 500 hp on a pump gas 383 they have comp cams 1.55 roller springs and comp cams stud girdles missing a couple of poly...

smae engine in my other post but selling short block with roller cam oil pan and front cover put your top end on and run it would make 630 hp wiht afr heads or something close message me or call 314-808-1061 will take partial trade on a set of sbc 215 64cc iron eagle heads

i have a fresh 434 sbc gm block with splayed caps eagle crank scat rods and 13.7 to 1 je pistons lunati roller cam pro topline heads all roller pro bilt dist with race demon carb high torque starter and sfi flexplate made 575 hp on the dyno i have the dyno sheets only dyno time asking 6500 OBO...

i have a fresh 434 sbc gm block with splayed caps eagle crank scat rods and 13.7 to 1 je pistons lunati roller cam pro topline heads all roller pro bilt dist with race demon carb high torque starter and sfi flexplate made 575 hp on the dyno i have the dyno sheets only dyno time asking 6500 OBO...

i have a fresh 434 sbc gm block with splayed caps eagle crank scat rods and 13.7 to 1 je pistons lunati roller cam pro topline heads all roller pro bilt dist with race demon carb high torque starter and sfi flexplate made 575 hp on the dyno i have the dyno sheets only dyno time asking 6500 OBO...

looking for a 24" chevy alunium radiator if any one has one cheap let me know thanks

looking for a msd billet or pro billet dist for a sbc if any one has one message me thanks

i have a 350 11.5 to 1 pistons all fresh has new 292 crane cam ported and polished 624 heads just redone has 780 cfm 3310 carb performer intake water pump and dist with wires ready to start asking 1500.00 OBO need money for new motor message me or call 314-808-1061