Search results

Dart Cnc Pro1 227's 2.08 1.60 valves Roller springs T & D shaft rockers (1.5 ratio) Heads, valves and springs have less than 10 nights on them. Edelbrock 2925 intake manifold by WILSON Aluminum fabricated valve covers Roller lifters and pushrods (for dart block) Schoenfeld 1186 headers...

Afr aluminum heads complete. SS valves and roller springs, studs, and guide plates. springs 4 races old with all fresh machine work. Crower rockers and Crower stud girdle with locks. Crower lifters Comp Cams Push Rods .080 wall Mullins Comp Cams used in engines 355- 400. Rotating...

24' Haulmark Enclosed trailer for sale. (white) Generator door with vent L shaped factory cabinets on floor Overhead factory cabinets across front Tire rack (8 mod tires and a trailer spare) with retractable air hose Aluminum/scissor mounted quartz lights at back -hard wired with a switch...

Looking for a set of 4 grain scales. Maybe just 2 even. Let me know what ya got.

25 night old bob Pierce Race car. #593 Out pace bars and heims tmw cages hyperco springs new bumpers all interior present including guages shifters etc. minus seat. all suspension parts front and rear. (Not somene's left over crap, good stuff) 6th coil assembly with removeable pin to...

06 Hoffman with all mounts and plugs for every combo possible. Even swing arm on both sides. We have a lot of extras for this car including springs,multiple pull bars, j-bar, short bar, front end pieces including but not limited to: upper a arm stuff lf lower control arm (Klushman bushings)...

95 silverado Turbo diesel 135k on truck. 25k miles or less on new crate engine from GM with a new injection pump and pdm. Good clean truck 85% 10 ply tires, clean interior, extended cab. Needs a little work on the a/c but all eqpt is there. Nice older truck just got a newer one. Would...

Can a quickener be ran at the aaraa tracks??

07 Pierce car all new stuff front to back and top to bottom. All you will need is your drivetrain/ engine stuff, battery, fuel line, seat and belts and you will be ready to race. This car is assembled with a complete body and all the good parts: out pace rods front and back and panhard...

07 Pierce Comp Roller -------------------------------------------------------------------------------- This car is as close to complete as you will get. Did I mention it has never seen the dirt? Brand new never raced, brand new parts all the way around. All the front end is there...

Complete '06 ,misc, and 358 -------------------------------------------------------------------------------- For sale is a '06 Hoffman Race Cars multi link car. Car comes with all bars and brackets for 4-4, 4-2, swing arm (both sides), z-link. Also comes with springs on current set up...

Nice set of Brodix 10 x heads. Ported, Polished with matching Bow tie intake. Offset rockers (crower) Jesel Shaft Rockers, new springs. All locks retainers stands bolts and hardware. 2.10/ 1.6 valves, 2 need replaced (all stainless) $1400.:D 618-554-6157

Stock block, splayed caps, alum heads (Brodix by AMS) crane roller rockers with girdle. 3.50 crank, 6" rods good fresh engine. Just has 6 nights on freshen. Will make a nice mod motor (7800-8300) or a terriffic spare. $4500 618-420-1075

04 Hoffman Modified 4- bar 4-bar or 4-z all here but engine, trans, shaft, gear. Some spares 618-420-1075 $4000 firm

Brodix track 1 2.08/1.6 stainless, with roller springs, guide plates etc...$700 hurricane intake... $100 Rons belt drive fuel pump with bracket and pill bypass... $175 Manley 4130 pushrods (NEW NEVER USED) 5/16 std lngth #25709-16...$90 Childs and Alberts track master rods (set of 8)...

04 Hoffman Multi link. Currently on 4 bar/4bar (lr clamp) roller bearing sliders. Z link capable. Roller bearing birdcages (A-1) both sides, Bilstein shocks Pell bar short panhard. Chevelle front clip/ corrected front end Bilstein shocks, Complete interior, including new Butlerbuilt...

'06 Pierce. Complete minus engine, trans, driveshaft and gear. Bp shocks, Hypercoil springs and pullbar. Complete interior and suspension including brakes wiring etc. Contact: 618-544-5444. $6000.00, Firm.

This is out of a 95 Chevy 3/4 ton. It has less than 100,000 miles and is in good shape. It is complete with with starter, ac stuff, power steering pump, water pump etc. $750. I also have a brand new injection pump for this engine (2500 miles) It can be left on for a additional $1000. It...

-------------------------------------------------------------------------------- ***Je pistons chev.400 4.140 3.875 stroke 6" rod 1.062 comp height 464 piston weight dome volume 2 $300 **Willys adjustable base plate not alot of these around. $200.00 **Edelbrock 13 psi alky...

23 degree aluminum Brodix 10XSP by Weldtech with matching bowtie intake. Completely ported and polished with all stainless valves, titanium hardware, and Jesel shaft-rockers, no springs. Excellent shape. $3500. Call for more info 618-553-1276 (cell) 618-586-2380 (home)