Search results

I have a 2006 Honda Recon 4 wheeler 4x2 - 5 speed auto with reverse very low miles. I have it for sale for (2500) Adult ridden , not raced or ridden hard. Been sitting, ready too go. Has a few scrapes on the rear plastics nothing bad. Still has not here big boy on the tires...

Hey I go the following up for trade - Here is link - http://www.racingjunk.com/category/72/Street_Stock/post/1912406/Street-Stock-For-Trade-.html

Hey racers, I am looking for a few good parts to try and get ready for 2010. Ok I am looking for a newer set of (Black or red) 6 point racing safety harness. Needs to be 08 or newer Also looking for a master disconnect switch, Also looking for either of the following items 16, 18...

oxygen and Acetylene Regulators for large tanks. May need hoses tooo. Let me know price and will need to be shipped. email me at racing24fan00@aol.com

Ok, Looking for a set of black complete belts with current dates, needs to be seperate tops, not the y type. Or if you have the y's give me price. Master disconnect Looking for 2 front fenders and drivers door to fit a monte carlo, old, pont, cutlass - Metric street stock. Also...

Looking for a large oxygen/acetylene cutting torch set . Looking for a full set of black 3 inch belts that are still in date 2008 or newer. Need to be single not the y type on shoulders. Looking for a master kill switch. Any one has anything pm me, include price and location and...

Hey guys, If you follow this link, all you need to do is sign up its all free you can find sponsors for all types of sports. Again its free, and heck take a chance and take a look. http://www.loopd.com/SignUp/SignUpAd...b-0032f9896d9d

Looking for a set of oxygen/acetylene cutting torch

Trying to find out what does it take to make a 362 small block chevy? any one who can tell me what it might take. thanks guys.

HERE IS LINK : http://www.midsouthforums.com/viewtopic.php?t=60625

SBC parts on ebay Here is link : http://motors.shop.ebay.com/merchant/whitesracing04_W0QQ_nkwZQQ_armrsZ1QQ_fromZ 4412 carb 1.5 3/8 roller rockers - RKE model SBC roller lifters New steel valve covers with gaskets reduction pulleys total 5 remote power steering pump with lines -...

Hey racers, I have a 9 inch Floater with a spood 620 gear. Its measured 67 inch outside to outside edge. It is 49 inches from outside sping pad to outside spring pad. It has leaf spring pad, brakes, and wide 5 hubs. Nothing wrong with it. I been keeping it for a spare but need t out...

Hey racers, I have a brand new racing seat which is a 17 1/2 - 20 degree seat. I bought it brand new seat. I did drill 2 holes in it, but thats it. The seat cover is new, no tears,just a couple of small dirt stains which will come out. It was where I tried bolting the seat in and found...

Going to be running a new track for next year. And here is the rules on engine. What I need is advise on cam and maker to get to these goals to stay legal. Car weight 3200 will be running a 1/4 and maybe a 1/2 mile track. rearend is 9 1nch. So to keep motor turning good rpm's what gear...

I have a terminator chassis built in Iowa, Imca rules has factory floor pans, fire wall, stock suspension. The car has a motor in it but it blown, has 7/16 rollor rockers, holloy 4bbl carb, racing fuel pump. alum radiator, GM Bowtie heads, Has Nine inch, racing springs, and shocks on all 4...

I have a terminator chassis built in Iowa, Imca rules has factory floor pans, fire wall, stock suspension. The car has a motor in it but it blown, has 7/16 rollor rockers, holloy 4bbl carb, racing fuel pump. alum radiator, GM Bowtie heads, Has Nine inch, racing springs, and shocks on all 4...

Ok i am running a 355 with bowtie heads std hei dist that has been locked and degreed. Solid lift cam. When i am at home or at the track and car is idling, its fine, go out on track and give it gas, the car will pop like a popcorn machine. go back to idle it does great. Can rev in pits...

Needing a tranny for a street stock- powerglide, 350 turbo short tail. I have a direct drive, that went junk last night racing. Needing right front spring 1100 lbs. Looking for hoosier emod tires. Also looking for a 4 1/2 bolt pattern bead lock and rim 2in offset. Let me know...

Im looking for a 750 gas carb for my street stock. Would like a double pumper,mechanical secondaries,with no choke or atleast the choke horn milled off. Must be in good shape. Not wanting to pay brand new price for a used carb. Email me at racing24fan00@aol.com Also looking for some 4 1/2...

Needing either a 650 or 750 double pumper carb. No vac secondary Would like to have the choke horn milled, but will take it if it doesnt. I need one like last week. Let me know what you got and cost, I am located in central indiana. so my need to ship to me. Just let me know cost...