Search results

Pulling a 92 buick roadmaster v8 this week. Engine and trans from a car that was on the road.Car is junk. Trading for demolition derby car stuff or firearms or ? Cash price..... make me a offer. Located paris il 61944. appx 2.5 hrs from st louis. Looking for 74-76 gm full size cars,all years...

I have a couple driveshafts from a aerostar van. They are aluminum. Something like 56 3/4" long to the outside of the u joints and take a 3 1/4" u joint. Anybody use these?

I have a 90 mustang with a 2.3/stick in it. Runs and drives engine runs great. Got slightly rearended so the bumper is gone. No damage to the frame as far as I can see but the pass rear quarter behind the tire is kinda banged up. What would it be worth to use as a racer? Any ideas got a guy...

Just Wondering What The Difference Was Between A 9" Rear And A 9" Nodular Rear. Are The Nodular Ones More Valuable?

I have a set of heads that are from a 77-85 350. The casting # is 376445. They are 76 cc chamber with small valves. All that is acording to mortec website. These were rebuilt by the local chevy dealer around 15 years ago. First they ran 2 nights at the local circle track. Then they were put on a...

I was looking for a 9" rear end under a narrower vehicle. Is there a easy way to tell a 9 from a 8 while it is under the car? Pretty new to this stuff so any help is appreciated.

I have a 350 that was rebuilt in a gmc jimmy. Trans is junk and so is the truck so I am wanting to sell this engine. It was pro-rebuilt less than 10,000 miles ago. 4v carb with accell ignition. Runs great. Looking for 700 obo. Located in paris il.

Selling for my cousin a 72 impala. It has a BB402/400 trans in it. Runs down the road at 70 just fine but prolly needs a tune up though. Vinyl top is shot. Interior is not show quality but useable. Exterior has very little to no rust. Frame is really good.Paint could be better. Newer 3 core...

Looking for a reverse mount brake pedal assembly. Like the wilwood ones that go inside the car. Short or long either one. Must be reverse mount.

Looking for 71-76 general motors station wagons. Must have rear leafsprings. Also looking for some 74-76 impalas or caprices. No m/t needed.

Looking for a steering nuckle/u joint that is splined to fit on a mid 70's general motors steering box. pm me here if you have one you can sell

I have been looking at a few alu. radiators and need some tech help on them. A few have had the lower neck up like 6 inches from the bottom. Most of these even have the upper neck right above them. Won't the water just make a quick circle and not even go through the fins? Where is the cheapest...

Needing one for a derby. I have a m/t so just need a rolling shell. Anybody got 1 where you pulled the m/t for your car and want to get rid of the body let me know. 74-78 mopar also

Taking a fishing trip by salem starting the 18th. I am looking to bring home a 74-76 gm sedan or a 71-76 gm wagon. No m/t needed just a roller is ideal. Also looking for 74-78 mopars. What do you have?

Taking a fishing trip by salem starting the 18th. I am looking to bring home with me a good derby car. Something GM in the 74-76 range for sedans or the 71-76 wagons. Please no rust buckets a little is ok but prefer them clean. 74-78 mopars also. Pretty much any of the old iron. What do you have?

Stahl utility bed from a 96 chevy 2500. This bed fits the curves of the truck.It is in great shape. White in color with a 1 year old bumper to go with it. No bends in the bumper it is white.Bumper fits the curves in the bed. Located in paris il. $500 obo

I have heard about stroking a 2.3 with 5.7 rods. Is this just pulling any rods out of a 5.7 or are there different years? Which bearings do you use. Is there specs or detailed instructions out there somewhere? Sorry I am so stupid but this is new to me. Putting this in a demo car so working on a...

Still looking for the front frame section for a 74 caddy. I think there the same up to 76 so I will try anything from 74-76. Gonna give up and junk the car if I can't find something soon. HELP PLEASE!!!!

Looking for a front frame section from a 74 caddy. Fresh,unbent,not derbied,and rusted out like mine. I will take a complete car if you know where one is that has a rusted junk rear frame like alot of them do. Also figured it was time for a new post on here. Owner of this site is nice enough to...

Looking for a 74 caddy near st louis or in illinois. CHEAP CHEAP CHEAP I live on the east side of illinois but looking everywhere. It does not need to have a m/t or even a rear frame. I really just need the front frame from about the drivers butt forward. Mine is rusted out and wanna put this...