Search results

I have a standard Bert trans 0 laps from rebuild $800 and a Bert bellhousing been professionally fixed(has run a full season since fixed) for $300. $1000 if bought together. Call Matt (309)-261-5476

415 All aluminum motor. Brodix block and heads all good stuff. 700 laps. $12000 or 14500 fresh. Built by Hixson Racing Engines. Call for more details. Matt Barker 309-261-5476

I have a 03 J&J for sale. Frame, body, 1 nose wing, 1 top wing, 4.86 Winter rear, 50" front axle with sanders spindles and direct mount hubs, complete driveline, pedals and master cylinder, kse full steering gear, and 28 gal fuel safe tank and bladder. $4000 I will also sell just frame...

I have an 03 Pierce for sale. New updated rear clip (by BPRC) in 07. New front clip (by BPRC) in 08. Good straight car. Has Winters quickchange. Right now its a weight jack car (LR) but easily changed to coilover. $4500 for roller. $5000 w/Bert, Bellhousing, starter, and driveshaft. Matt Barker...

410ci Dart little M block, Callies crank, Carillo rods w/ Carr bolts, JE Pistons, Crower lifters, Cloyes Hex-A-Just chain. Brodix -11 cnc'd by Gearte heads w/ Tool Room 9985 valve springs, T&D shaft rockers. Bowtie intake, Olson 9qt steel pan, SW Stage 3 water pump, ATI crank hub. Built by...

Brodix track 1 heads with all new stainless valves. (2.10/1.60) No damage ready to bolt on. 64 cc combustion chambers 221cc intake runners. Nearly new Isky Tool room 9985 valve springs (245lbs seat and 600lbs @ 1.300") $800 Call Matt 309-261-5476

Have a set of Shoenfeld 1186 Headers for sale. They are standard 23 degree chevy flange and at the most ran them 10 nights. Not dinged anywhere except on left side muffler. $175 Call Matt 309-261-5476

Rodeck Aluminum Block. 4.160 Bore, 350 mains, 9.010 deck height, STD cam bearings and location, STD pan rails. Dry sump ONLY. Block was New in 2000 from Gearte. All threads in great shape. Block has NOT been blown up. Good piece. $1500. Call Matt 309-261-5476

TRC titanium 6.0in rods. Rods are in great condition only about 500 laps on them. 2.100 rod journal .927 pin diameter 1.055pin end width .938 rod end width. $1200 OBO Matt Barker 309-261-5476

Barnes 3 stage oil pump with Gilmer pulley w/guides. Good condition. Has been gone through. $400 Matt Barker 309-261-5476

Barnes 3 stage oil pump with Gilmer pulley w/guides. Good condition. Has been gone through. $400 Matt Barker 309-261-5476

Winters 9" for a Pierce car. Bare housing and axles with lift bar and pullbar mounts welded on $450 Housing with all brackets installed $650 Barker Motorsports Matt Barker-309-261-5476

1996 Dodge Ram 1500 4X4 156,000 miles. Standard cab long bed. Runs and shifts great. Grey(typical dodge paint coming off) Solid truck $3000 Matt Barker (309)-261-5476

Set of Dart Sportsman II heads. P/N 1115B 2.02/1.60 valves. 200cc intake runners 64cc chambers angle plug. Complete but probably need new valve springs. $450. Matt Barker (309)-261-5476

I have a 355 motor for sale. fresh machine work on block. New pistons, cam, lifters, timing chain, and balancer. Fresh polish on crank and refinished stock rods. Also have a set of steel GM heads (1.94) that go with. $1500 Matt Barker 309-261-5476

I need a set of 6in large journal H beam rods asap. Need them on the cheap not looking for anything new or fancy just trying to get back on the track. Matt 309-261-5476

Pierce chassis #172 new rear clip in 07 and new front clip at end of 08 (2 nights this year. Complete roller w/ QC(4.12 r&p) minus motor, trans, bell, seat and ignition. $5000 this is my bottom dollar it's all quality stuff and it will sit in the garage if I cant get that out of it. Will put...

Barker Motorsports is now selling Torco methanol for $175 per drum plus tax. If interested call Matt @ 309-261-5476

Barker Motorsports is now selling Torco methanol for $175 per drum plus tax. If interested call Matt @ 309-261-5476

Barker Motorsports is now selling Torco methanol for $175 per drum plus tax. If interested call Matt @ 309-261-5476