15 inch kirkey lightweight seat with right side head rest - great shape $150
Tilton magnesium sbc bellhousing - no cracks, repairs or chips $150
Steel sbc bellhousing $50
like new sbc standard mount starter for 153 tooth flywheel $50
lightweight sbc flexplate 153 tooth - like new $40
standard...
15 inch kirkey lightweight seat with right side head rest - great shape $150
Tilton magnesium sbc bellhousing - no cracks, repairs or chips $150
Steel sbc bellhousing $50
like new sbc standard mount starter for 153 tooth flywheel $50
lightweight sbc flexplate 153 tooth - like new $40...
I have a 602 completely disassembled with everything but the camshaft.
Heads need a few valves replaced. Camshaft broke and bent a few valves.
Heads have no cracks.
Oil pan, intake, block, crank, rods, pistons, all bolts, valve covers, pushrods, timing chain, etc...
If you are looking to put...
I have a used bert trans (non ballspline). It was a back up in the trailer the past two years. It had new clutches in it when I bought it from a guy. I never put it in the car or hooked it up so I can not verify if it works correctly or not. I just want to be honest and clear on it. I can...
Complete 602 rotating assembly from a low laps crate engine.
Complete crankshaft, rods, pistons (rods and pistons are still fitted together), and bearings.
Great condition. Had a head problem so I disassembled the engine to part it out.
$500
Rampovers that are in a 24 foot enclosed trailer.
183 inch total length
11 inches high
24 inches wide
made from 1x1 tubing with wood top
located near Peoria, Illinois
$300
MRE rocket modified
metric chassis with nova lowers
pullbar or lift arm (currently on pullbar)
winters quickchange
4/4 or zlink
afco calipers
bsb slider
bsb roller bearing birdcages
wehrs machine jbar and chain limiter
15 inch kirkey seat
new gauges
msd with coil
two sets of headers (one for...
7 nights on GM sealed 602 crate (gm factory seals).
Broken in on dyno using Joe Gibbs oil.
Only used Joe Gibbs oil in engine to race.
Dynoed and ran on 93 octane pump gas. I have the dyno sheets for buyer.
Includes stewart stage 2 water pump, 1:1 pulleys, 4 blade fan, 153 tooth flywheel with...
358 sbc with 010 block
Howards forged crankshaft
Howards 6.00 inch forged rods
SRP pistons
custom ground flat tappet camshaft
billet center main caps
Dart steel heads
Edelbrock 2999 intake
stud girdle and roller rockers
one season on complete new build with only 4 races this season since...
Rayburn 104-4 setup on 4 bar
7 race old GM sealed 604 with extra beehive springs
7 race old JDR Holley UltraHP crate pump gas carb
Schoenfeld triple stepped headers with anti reversion mufflers
7 race old MSD pro billet crate distributor with moroso wires
MSD 7AL high voltage box
reverse mount...
Rayburn 104-4 setup on 4 bar
7 race old GM sealed 604 with extra beehive springs
7 race old JDR Holley UltraHP crate pump gas carb
Schoenfeld triple stepped headers with anti reversion mufflers
7 race old MSD pro billet crate distributor with moroso wires
MSD 7AL high voltage box
reverse mount...
Brodix track 1 aluminum heads just freshened
Brodix HV1000 intake with cooling lines
New 1.6 Scorpion race roller rocker arms with stud girdle
Trend pushrods
Aluminum valve covers
Dyno time and one race only on top end.
Changing direction in my racing program is reason for selling.
$1400 obo
Rayburn 104-4 currently setup on 4 bar.
Car has brand new AFCO shocks. RF and Fifth coil are rebound adjustable.
Traction shock is compression adjustable.
Brand new wiring fuel lines.
Sweet rack
Has double pass radiator
MSD 7AL box
16 inch seat
Wehrs machine shifter with rods
Wehrs machine...
New 400 shortblock with everything listed below.
Brand new Dart SHP block
New Callies 3.750 stroke compstar crank
New Callies 6.00 inch compstar rods
New SRP hollow dome lightweight pistons
New bearings, rings, etc...
New custom ground Custom Cams camshaft with Cloyes timing chain
New balancer...
14 races on a complete Race1 604. Willy's e85 external adjustable jet metering block carb, cv billet fuel pump, water pump with low drag pulleys and 2 blade hendren fan, msd distributor, bert coupler, and late model headers. This is complete from carb to pan, fan to coupler. Drop it in and run...
14 races on a complete Race1 604. Willy's e85 external adjustable jet metering block carb, cv billet fuel pump, water pump with low drag pulleys and 2 blade hendren fan, msd distributor, bert coupler, and late model headers. This is complete from carb to pan, fan to coupler. Drop it in and run...