Search results

i have a 350 sbc out of a 87 camaro for sale it comes with a power plus intake manifold and carter afb carb ,starter,alternator,distrib,radiator,electric fans.. also have a 700r4 transmission and torque converter asking $350 obo. located in champaign il.

craftsman 30 gallon black tanked vertical air compressor for sale. has some paint on it but works perfectly and has been well maintained. can include hose filter with it 125$ obo it is located in champaign illinois.

on a metric stubbed car how far back from the front does the stub need cut? at a minimum... we are talking about using the kit from speedway motors for the frame and want to make sure they didnt cut the front stub off to short.

handler 125 mig welder can be converted to gas works good just dont have much use for it.asking 200 plus shipping.

i have a metric stub for either a modified or sportsman chassis or could be used to clip a metric street stock... its free just want to get it out of my yard... located in champaign illinois

anyone race at charleston speedway that knows if trucks are allowed in the hornet class?????

i have a newer hobart handler 125 setup for flux welding can be converted to gas for sale used less then 1 hour total will include a new roll of wire and extra tips with it and a partially used roll of wire... asking 175$ plus shipping for it.

i have a 2000 tnt overrail 4bar/zlink chassis for sale. comes with motorplate,32 gallon fuel cell,seat with cover,belts,front control arms front spindles,all 4 springs,gauges and ignition panel. interior is in it its black interior on a black chassis. will also throw in a steering wheel...

i have a metric stub for sale asking 50$ the way it sits or 65$ if you want it sandblasted before pickup... the stub is straight and not bent and is ready to slap onto a modified or a sportsman chassis. it is located in champaign illinois

i have a 98 tnt chassis that comes with the interior.front control arms and spindles plus the gauges and tach and a manual rack n pinion. looking to trade it for a bare modified chassis. close to central illinois.

looking for some coil over kits. front and back

1 brand new 16 5/8 lower control arm with brand new screw in ball joint 1 brand new 17 5/8 lower control arm with screw in ball joint 45$ 1 set of used wide 5 spindles with locknuts 8 3/4 tall 45$ 1 set of wilwood starlite magnesium hubs with brand new bearings and seals installed for the...

newer xbox.. with one controller,one memory card. and the following games. juiced shell shock nam 67 major league baseball 2k5 crimson skies espn football nascar 06 total team control forza motorsports and ms pacman. will also throw in the subscription card i have for xbox live and the head...

looking for some pictures of open late model trailers. getting ready to start building my new trailer and just want to get some ideas of how to setup the ramps and weather to dovetail it or not...and to get some ideas of tire racks

looking for some to make 2 setup at 16 1/2 center to center of the heims and 2 at 25 1/2 center to center of the heims... 3/4 inch size for all of these.

looking for some beat up or bent wide 5 wheels would prefer with tires. tires can be useless long as they hold air.. just looking for something to make the chassis a roller so i can send it over to get the body and decking put on without having to order the new rims for it yet...

welder is less then 6 months old been used 4 times. retail is 435 asking 350 or trade for a older quickchange for a latemodel. welder can be used with gas or without it is currently setup for gasless welding.

looking for 2 3/4 rh thread rod ends and a spanner wrench for screw in lower ball joints...

looking for a used dirt late model body for a friend. color doesnt matter.. would prefer something close to central illinois.

looking for 2 front springs one 500 lb one 400lb 2 rear springs one 275 lb and one 225 lb 4 link bars swing arm 15-19 inches swing arm birdcage regular 4 link birdcage.