Search results

Tubing bender for sale, bought new from Speedway Motors. gave around 375.00 new it has been used to built two car's. great condition, has 1 1/2 die's with it. 175.00 firm call 618-267-0136 or e-mail stringtech@aol.com

I have a pair of modified headres they were only used 3 or 4 nights. were on a Harris modified asking 50.00 I have a set of used Rebco scales that I no longer need. Bought them new a few years ago cost over 1,100.00 they work great. Will take 500.00 618-267-0136 cell or 618-547-3649 home...

I have a set of used Rebco scales that I no longer need. Bought them new a few years ago cost over 1,100.00 the work great. Will take 500.00 618-267-0136 cell or 618-547-3649 home. Located in Kinmundy, IL

Simpson fire suit, Bob Pierce custom suit used 1/2 season. I am 6-00 tall 190lb gave near 600.00 first 300.00 takes it 618-267-0136 or e-mail at stringtech@aol.com

Winters 9in rear housing,axles,bird cadges, lift bar every thing except hubs out of an 08 Pierce mod. Pierce teardrop fuel cell and straps out of same car 1 pair of stock metric spindles 1 pair of new in the box U.S. brake metric rotors 5x5 4 new braided brake lines Will take 400.00...

used shocks are BP4D-1 and BP1

The new shocks are BP3D and BP1D

2006 modified chassis #440 has new front stub 1400.00 9 inch rear housing w/all brackets, mounts and axle's (no hubs or gear ) 400.00 Pierce teardrop fuel cell 200.00 2 new BP shocks 100.00 ea. 2 slightly used BP shocks 60.00 ea. New Afco 90-10 aluminum shock 75.00 Located near...

06 Pierce roller for sale, 6000.00

New Bert ballspline trans, never been raced gave 1600.00 for it will take 1100.00 firm. Ford 9 inch 3rd member 31 spline full spool light weight gears ready to bolt in been ran 6 or 7 nights 400.00 618-267-0136 located 10 miles north of Salem, IL

New Bert ballspline trans has been put in the car but never used 1,200.00 9 inch Ford 3rd member 31 spline full spool been used about 3 nights 350.00 618-267-0136 or e-mail mod15racing@aol.com located about 10 miles north of Salem IL

I have a 2000 Rayburn late model chassis that needs a front clip, if anyone can use it I will take 150.00 for it. chassis and cockpit. 618-547-3649 home or 618-267-0136 located about 10 miles north of Salem, IL

SB Chevy 383 short block, Cola 4340 crankshaft, JE pistons (13 to 1 with 64 cc heads) Scat 6.00 H beam rods. Bullet roller cam and lifters. 4 bolt splayed main caps. Arp head studs. aluminum water pump.just needs your heads and intake. the motor was built by Weber machine in Olney, IL has just...

Willys alky carb fresh rebuild 500.00 Dart Pro 1 aluminum heads 215's 2.08/1.60's 64 cc comp cams roller springs.the heads were used 1 night last season then taken off and took to the shop this year for port work, they have been bowl blended port matched to a Edelbrock super Victor intake...

I have 2 ford 9 ince 3rd members 4 sale both are 31 spline full spool, the 5.83 have been ran 1 night since new. The 6.33's have been on the track 3 nights. the 6.33's are also the light weight gears. 300.00 each. call 618-267-0136

I have a Pierce mod bare chassis with the cockpit decking and roof will take 750.00 for it.

back to the top

back to the

If anyone needs a new modified call and make an offer, it's a good car.

sbc 383 , 4 bolt splayed mains,Cola crankshaft, 6.00 Scat H beam rods, JE pistons, roller cam, Dart Pro 1 aluminum heads 2.08 / 1.60 valves, Edelbrock 2925 intake, the heads have had some port work and have been port matched to the intake (1206 gasket). Comp cams springs and roller rockers. The...