I have a set of +.030, 13 to 1, 350 w/5.7 rod, Manley pistons for sale..These were used in a Drag car, and are in great shape. They mic perfect. I have pics..I also have 2 GM, Std./Std. cranks. These haven't been raced. Balance, polish and go racing..$140 ea...PM me w/questions or offers..Thanks...
I have a just rebuilt Holley 850 Gas carb. It is in great shape. I used a good Holley kit w/non-stick gaskets, nylon gaskets where ness.,.110 needle & seats, welded throttle shaft so it won't slip or come loose, milled T.shafts, 1 11/16 bore baseplate,...Asking $275..I'm in High Ridge, Mo. Might...
I have a nice Std. bore 454 block, New Std./Std. cast/steel crank, 1 set of New .340 Domed pistons, +.030 Moly rings, 1 set of K.B. flat top pistons, used 1 season in a boat, and a Edelbrock intake. PM me or post any questions..I'm open to offers. Would trade for SB engine parts..Let me know..Thanks
I have a Brand New Scat 9000 3.750 stroke crank and Clevite 77 Brgs., and a set of Speed-Pro flat top, 2 reliefs, coated skirts, +.060 pistons w/ Moly Rings..GM rods, shot peened and resized with ARP bolts. $450...I'm over around House Springs, Mo..PM me or post here..Thanks
This is for my neihbor..His daughter slid under a new van..Broke the AC Condensor and Rad..Car hs 70K. Runs and drives fine. They only had liability on it..He want's $700 OBO..Trans. (Auto) is good, half shafts, computer, etc..Clear title..
I have a 350 +.040, 2 bolt shortblock for sale. Block, 1 valve relief pistons pressed on X-Rods, ARP bolts, .010-.010 steel crank, all balanced,it ran great when I took it apart. Freshin it for next year, (Rings and Brgs.) or total rebuild it. It's a '69 block, VERY nice metal in it w/very...
388 Parts:: All parts are Brand New...Lower price..
I have a Scat 9000 crank, New in the box, w/Clevite 77 brgs $225. I also have a set of Speed-Pro flat-top,+.060, 2 valve relief pistons, w/S-P Moly rings. $200...Or make me an offer on it all..It's all still in the boxes..Let me know..PM me or...
I have a Scat 9000 crank, Moly rings, Speed Pro Hyper pistons, Clevite 77 Rods and Main Brgs. Pistons are flat top w/2 valve reliefs..Crank-Std, Pistons+.060 $425 PM me or post..
I have a steel crank I took out of a running engine. (350) Had great oil pressure. It's .010-.010, mics great. Might polish it before using it. $125 PM me or post here..Thanks
'99 Jimmy, 4.3, auto, 4 wheel, $1000! NEW PRICE!
I have a '99 Jimmy with a 4.3 Vortec, 110K, drivetrain perfect, slight rollover, clear title, runs and drives great,engine, trans., transfer case, rad., etc.. PM me or post here..Thanks..Will trade for good SBC racing shortblock
I have a '99 Jimmy with a 4.3 Vortec, Auto trans, 4 wheel drive, 110K, LIGHT rollover. Motor runs great, drives fine. Will trade for 377 or 406 shortblock. $1200 obo Let me know what you got. Please PM me or post here..Thanks...CLEAR TITLE
I have a Holley #4778, 700 cfm DP, just rebuilt with all Holley parts. Ready to bolt on. $150 I also have a Holley #4412, 500 cfm 2 BBL, just rebuilt with all Holley parts. $130 Both are in great shape..Thanks and PM me or post here..I can also do some tricks to either one for a little extra.
This is a 750 gas carb, 4 corner idle circuit, Throttle shafts shaved, all they're little tricks, it was bought new in 2002 for a boat. Used VERY little. I have there build # off it. Needs a kit, but I pulled the bowls off and looks new. $240 or $285 w/a Holley rebuild. Thanks and please post...
I have a just built Holley 4778.(700 dp) It has all Holley parts..Nice piece, $150...A set of 1.5 and 1.6 Comp. or Harland Sharps roller rollers w/polylocks. Wide orange bodys..$130...Comp Cams roller tips. 1.52, grooved balls, $60 PM me or post here..Thanks
I have a brand new Holley part #80542-1. It is a 650 cfm Methanol carb. It has dual 50cc acc. pumps, 4-corner, Progressive mech. secondarys, Nitrophyl floats, jet extensions, Stainless Steel butterflys, more..$675 in the books..$450 Please PM me or post here..Thanks
The first pair is a bare set of 487X's. They were baked, new bronze gudes installed and honed to size, I have all the hardware if you want it too..$150
The 2nd set is a fresh pair of 462's with Manley 1.94-1.500 valves, Bronze guides, Hard exhaust seats, Screw-in studs, Good springs and Moly...
I am looking for a set of +.030 355 pistons. Could use a 5.7" or 6" rod.. TRW, SRP, K.B.'s. Prefer 6", but would listen to what you have. Please PM me or post here..Maybe a shortblock??...Thanks
What was up with the #32 Sportsman car slamming into J.G.#18 while the corner flagman wasn't ever looking? These guys have alot of $$$ in these cars and this stuff isn't good for any one!! I know 32 is a rookie and runs in the back alot, but stays out of trouble..It's a no win deal...
I have a set of full roller rockers and polylocks, 1.5 x 7/16. They're blue, Omega-Proform, in the box, never used. Bought some swap meet shaft rockers instead. $125 or trade for Double pumper Holley. 700-850 cfm. Let me know what you have..Please post or PM me any questions..Thanks
Can anyone tell me how to run a late model Alt. with just one charging wire? Mine has 4 wires into into the alt. with a plug and one bigger wire on the back. I don't know anything about these later models. Thanks in advance.. Howard:confused: