Search results

Brand new air pumper never used in original box yet, Will take $100 for it. Call 618 593 9084 Thanks, Mike

Dirtworks DW-8 Roller $2200 Dirtworks dw8 roller, less motor, trans, & gear. New UB lowers, qa1 rebuildable ball joints, shaw upper a arms. Qa1 shocks, short four bar rear with z link option on right rear, 9in rearend, hawk brake pads. Ball bearing birdcages, dual acting pullbar. You will...

1. Servi-quip boring bar on stand with tooling. Bore v-8, v-6, motorcylce cylinders. Rottler type of machine. $3000. 2. Jet wash cabinet, nice smaller model, $2800. 3. Small Hot Tank for dipping blocks and etc. Natural gas or propane, 5ft.x4ft.3 1/2 tall. $350. 4. Van Norman Broach, for...

Looking for a T10 SUPER four speed with fine spline input and 400 tailshaft, Please PM me on here or call 618 593 9084

I am in need of an engine for my work car. Looking for anywhere between 1992-1996 engine. Let me know what you have. Please call 618 593 9084 or PM me on this board Thanks Mike

Bad Brad Haas will be piloting the 28 modified on friday the 21st. For all that remember him from the past it should be an exciting night.

Good to see you run great tonite, congrats on a great run from Haas Heads and Performance engines. Shane especiallly

Looking for a big C&S gas 2 barrel carb . Call 618 593 9084

Carb has 25 nites on it. Bolt on and go. will take $400 or looking for e85 carb to trade. Carb is set up for oval track. call 618 593 9084

what is the qualification for rookie of the year at belleville in the modified class? How many nights does it take to be eligibile or to be considered a rookie. Can a person race at a track for a number of nights the year before and still be considered for ROY?

5 by 4 3/4 bolt pattern. 4in. offset 8in. wide $30 like new only mounted a tire on it. call 618 593 9084

Taken off my trailer, ready for yours. Made of treated lumber. $60 for the pair. call 618 593 9084

Looking for a set of .060 over domed forged pistons for 6" rods. Looking to build a project motor. Post on here what you have or call 618 593 9084. Thanks. Mike

JE pistons 4.155 bore 1" compression height with .100 dome for 18 degree heads. Uses a 4"stroke with 6" rods or 3.75" stroke with 6.125" rods. Can be used with 23 degree heads with smaller cams. Includes wrist pins, spiral locks, and backup rings. Cleaned and ready to go. $80 JE pistons...

Kwik way boring bar with stand to bore small cylinders, come with all tooling and centering finger sets for sevaral size bores. Can be bolted to a block and bore cylinders. $500 Aeroil Hot Tank for degreasing blocks,heads, etc. Tank measures 45"x42" by 36"tall. Uses natural gas for...

Sundance hot tub seats 5-6 with lounger. Older model that works great. Tub is white with wood cabinet that needs paint or stain. It does need a new cover. Needs 220-50amp service to power. $900 Call 618 593 9084 Thanks Mike

One is a FMC set up for drums and needs the power feed fixed, the other is a Van Norman set up for rotors, it needs a belt for the power feed to work. There is tooling that goes along with both. $200 for the pair. Call 618 593 9084 for info.

I guess since the feature winners the past 3 weeks have been no-name people, the results haven't made front page news. These people have sponsors and could be recognized as winners also, not the chosen few. Signed Mike Haas

I am looking for a 32 1/2 to 33 inch driveshaft. Call Mike at 618 593 9084. Thanks Mike

I am looking for a 32 1/2 to 33 inch driveshaft. Call Mike at 618 593 9084. Thanks Mike