Search results

Sell or TRADE. BBC 3872702 closed chambered heads. Oval port. 98cc combustion chamber. These with wake up your low compression motor!! Fresh valve job, 2.19/1.72 valves. New intake valves, bronze intake valve guides, hardened exhaust valve seats. New springs for a flat tappet cam up to .600...

Everything is BRAND NEW. This includes EVERYTHING to assemble this motor, all machine work is done, all parts included. Crank and cam are already installed. 14015445 4 bolt main block, 3987416 FORGED crank, 3872702 closed chambered heads, KB257 12:1 dome pistons, Eagle style H-beam rods...

SOLD .

Sold

Sold sold sold

4 pro build flatheads, all plate motors on methanol, complete ready to run with air filter, pipe, muffler, chain guard. 2- L&J, one Pole Cat, one Checkered Flag. $200 each. Ready to Run!!!!!!!! Bunch of flathead parts. What do you need? older floor mount fuel tank. 1 gallon?? $20 15 degree...

2- tierod assemblies, used, includes inner tie rod, swedge tubes and heims 1- 8 3/4 one piece upper control arm for a screw in ball joint, aluminum shaft, used, 1 set- stock pinto/mustang II spindles, never ran, reamed 1- GM "Z" steering box, from a metric frame, GOOD, never ran 1- LF...

2- tierod assemblies, used, $25 for the pair 1- 8 3/4 one piece upper control arm for a screw in ball joint, aluminum shaft, used, $15 1 set- stock pinto spindles, never ran, not sure if they are reamed or not. $125 for the pair 1- Big GM "Z" steering box, GOOD, never ran, $75 1- LF Granada...

Floater setup for a metric car. Looks just like a Winters Grand National in the Speedway catalog but the axle caps say ACE. Excellent, straight, complete, rearend with brakes and 31 spline axles. 5 on 4 3/4 wheel pattern. $600 firm. I also have the cage that I cut off of my metric Factory...

58" floater setup for a metric car. Looks just like a Winters Grand National in the Speedway catalog but the axle caps say ACE. Excellent, straight, complete, rearend with brakes and 31 spline axles. $600 firm. Edelbrock Performer RPM 7101 for SBC, square flange, $75 or trade for a good 2101...

58" floater setup for a metric car. Looks just like a Winters Grand National in the Speedway catalog but the axle caps say ACE. Excellent, straight, complete, rearend with brakes and 31 spline axles. $600 firm. Edelbrock Performer RPM 7101 for SBC, square flange, $75 or trade for a good 2101...

This is an 400 SBC, 817 block, line honed, .040 over with a stock 10/10 crank, rods, and stock style pistons. It has a Speedway special .500 lift solid cam, 194/150 valves, 76cc chambers, pinned studs, and long slot rockers, GM aluminum intake, 'custom' HEI distributor w/ external coil. I'll...

I only raced 6 nights in 2010 and won 3 heats and a feature at Dallas County Speedway in this car. Metric chassis, weight jacks, Grand National Floater that I just put in this winter, 5 on 4 3/4 all around with 5/8 course lugs, Pro shocks up front, Bilsteins in the back, KRC power steering...

This is a nice carb that came off of a TRX400EX. I'm sure it will fit other models or engines. Bought the bike but I'm not a racer so I've put the stock carb back on it. I've got the dual cable twist throttle setup to go with it also. It includes the intake adapter for the EX also! $200 for the...

Street Stock for Sale or Trade It's time to do something else until the kids grow up a little bit. I will sell this as a full roller or I've got a short block I will sell with it also, maybe even a powerglide setup. I only raced 6 nights in 2010 and won 3 heats and a feature at DCS in this car...

Bought this from a guy who was hauling a late model on it. Bought new in 2004 from Branson Trailer. 18ft production trailer, dovetail, brakes, tire rack. Good Missouri Title. I would like to trade for a similar production trailer that I can haul my street stock on or my small tractor. No...

I've got a brand new set of 103 schoenfeld headers. Wanted to do some over the rails on my metric car but I would have to do to much modifying to make these work. The 107's wouldn't work for several reasons. 1 5/8 primaries, 3 inch collector. THESE WOULD WORK GREAT ON A SPORT MOD, MIDWEST MOD...

PM or call. 573-220-8412. Trade for racing related stuff, I need a decent gas DP 750 holley, 28 spline full spool, over the rail headers for a metric car???, whatcha got?. Paypal or cash. I'll only ship it if it fits a USPS flat rate box. I live near Springfield, MO. Wheels- 5on5 15X10 bead...

I've got a set of 16X4 1940 Ford Wheels with WWW motorcycle tires to fit them. $100 for all <br> 3 bucket style "bus" seats, good for a roadster or whatever. $20 each <br> Early manual Mustang steering box, All new bearings and seals. $75 <br> 1940 style original transverse front spring. $50...

This motor has never been in a car or raced!!! It came out of a 1998 Bandit bike with 36k on it. IT HAS A FRESH VALVE JOB AND A NEW CLUTCH!!! Dogs on tranny gears are in good shape, shifts in to all gears smoothly. Completely stock. This is for the complete motor assembly, starter, and a beat up...