We are out of LM racing and still have the motor and some assorted parts.
362" open motor. Built by JD Wyman Motorsports. Yates heads with matching intake by Ernie Elliot, Motorsports 9.2 deck block with valley cut down for weight, Bryant crank (302 main, SJ Chevy rod), Carrillo H-beam rods, Weisco pistons, Isky Red Zone lifters, Roller cam, Jessel Shaft rockers, spring oiler valve covers, aluminum dry sump pan, Hy-Vo timing set, 6 nights on motor. Never hot, never over 8400 RPM, ready to go. Will throw in 2 sets of headers and a spare aluminum dry sump pan. 1 set new and one set with 6 nights on them. $8250
Does not include pulleys, distributor, water pump, fuel pump, wires, ignition, fan, mounts. Will include the spring oiler lines on the valve covers but no other lines.
Ford 27.5 x 19 AFCO radiator. 6 nights, absolutely like new. Hose on left lower, AN for uppers on right tank. $200
Also have a Bert aluminum bell with Ford drive setup. $200 for bell and flywheel. Bell has been welded before but works fine.
Also have an Appleton rack and servo. 6 nights on rebuild, no damage but could use a left boot (torn), 19.25 wide, 3.4 ratio. Ready to go. $250
AFCO threaded body shocks:
1393-5 w/ c/o kit
1394-0
1396-3 w/ c/o kit
1395 w/ c/o kit
1376 w/ c/o kit
1373-5 w/ c/o kit
1375-3 w/ c/o kit
$65 each or all for $350 (save $15 per shock) these are either new of fresh back from AFCO. No damage, no junk.
QC gear sets
5.78
5.95
6.13
6.32
6.39
6.57
6.71
6.90
6.95
7.04
7.15
7.26
7.42
Some of these are new, never run. No junk gears. Your choice for $25 each or all of them for $300
AFCO springs. All are coilover springs and other than noted are like new. All have been rated and are engraved.
175-14"
200-14" (this one has some coating chipped off and looks a little older, still rated good)
200-14"
175-12"
200-12"
275-12"
275-12"
300-12"
450-12"
550-12"
225-10"
250-10"
300-10"
350-10"
400-10"
425-10"
430-10"
500-10"
500-10"
535-10"
550-10"
600-10"
650-10"
$15 each or $300 for all
Scavage in-line oil filters.
3 have -12 in and out with a 90* on one end. These are Peterson. These are new!
5 have -12 in and out and are straight on both ends. These are Moroso, like new.
$40 each or the first $275 takes them all.
All prices are plus shipping.
PM me here for more info.
Thanks,
SPark
362" open motor. Built by JD Wyman Motorsports. Yates heads with matching intake by Ernie Elliot, Motorsports 9.2 deck block with valley cut down for weight, Bryant crank (302 main, SJ Chevy rod), Carrillo H-beam rods, Weisco pistons, Isky Red Zone lifters, Roller cam, Jessel Shaft rockers, spring oiler valve covers, aluminum dry sump pan, Hy-Vo timing set, 6 nights on motor. Never hot, never over 8400 RPM, ready to go. Will throw in 2 sets of headers and a spare aluminum dry sump pan. 1 set new and one set with 6 nights on them. $8250
Does not include pulleys, distributor, water pump, fuel pump, wires, ignition, fan, mounts. Will include the spring oiler lines on the valve covers but no other lines.
Ford 27.5 x 19 AFCO radiator. 6 nights, absolutely like new. Hose on left lower, AN for uppers on right tank. $200
Also have a Bert aluminum bell with Ford drive setup. $200 for bell and flywheel. Bell has been welded before but works fine.
Also have an Appleton rack and servo. 6 nights on rebuild, no damage but could use a left boot (torn), 19.25 wide, 3.4 ratio. Ready to go. $250
AFCO threaded body shocks:
1393-5 w/ c/o kit
1394-0
1396-3 w/ c/o kit
1395 w/ c/o kit
1376 w/ c/o kit
1373-5 w/ c/o kit
1375-3 w/ c/o kit
$65 each or all for $350 (save $15 per shock) these are either new of fresh back from AFCO. No damage, no junk.
QC gear sets
5.78
5.95
6.13
6.32
6.39
6.57
6.71
6.90
6.95
7.04
7.15
7.26
7.42
Some of these are new, never run. No junk gears. Your choice for $25 each or all of them for $300
AFCO springs. All are coilover springs and other than noted are like new. All have been rated and are engraved.
175-14"
200-14" (this one has some coating chipped off and looks a little older, still rated good)
200-14"
175-12"
200-12"
275-12"
275-12"
300-12"
450-12"
550-12"
225-10"
250-10"
300-10"
350-10"
400-10"
425-10"
430-10"
500-10"
500-10"
535-10"
550-10"
600-10"
650-10"
$15 each or $300 for all
Scavage in-line oil filters.
3 have -12 in and out with a 90* on one end. These are Peterson. These are new!
5 have -12 in and out and are straight on both ends. These are Moroso, like new.
$40 each or the first $275 takes them all.
All prices are plus shipping.
PM me here for more info.
Thanks,
SPark
