looking to buy modified
- Thread starter 29L
- Start date
rvincent21
rvincent21
2006 Pierce Modified $6,000 or make offer (Please see link for pictures)
Would sell with bert transmission, bert bellhousing, and bert starter for another 1,000
Updated '07/'08 rear stub
Outpace tie rods and trailing arms
Ford 9 inch rear end with 620 gear
hypercoil springs (has newer springs
Hawk Brake Pads
US Brake Calipers
Tubular lower A-Arms
Digital Tach/6 AL Box
Afco shocks
lots of spare parts (front/rear bumpers, upper/lower control arms, 2 howe ball joints, 4 replacement ball joint studs, 2 complete tie rods, 2 outpace trailing arms
this car was always quick anywhere we took it. only has 2 nights on it this season.
if your interested call jerry grither 314-707-0479
Would sell with bert transmission, bert bellhousing, and bert starter for another 1,000
Updated '07/'08 rear stub
Outpace tie rods and trailing arms
Ford 9 inch rear end with 620 gear
hypercoil springs (has newer springs
Hawk Brake Pads
US Brake Calipers
Tubular lower A-Arms
Digital Tach/6 AL Box
Afco shocks
lots of spare parts (front/rear bumpers, upper/lower control arms, 2 howe ball joints, 4 replacement ball joint studs, 2 complete tie rods, 2 outpace trailing arms
this car was always quick anywhere we took it. only has 2 nights on it this season.
if your interested call jerry grither 314-707-0479
Herndon Racing
New Member
2009 Shaw by All (Taylor,Landers,Herndon)
The car has only been run a little over 20 times and has 11 feature wins. The car started out as a Taylor car and before the Texas race I took it to AR and put on the jig and made sure everything was straight. While there I had Landers to put his four bar and pullbar brackets on the car and do some frontend work. Everything on the car was new at the beginning of the year. Has Tilton brake pedals , brand new brake calipers, tiger thermal coated quickchange rearend, BSB birdcages,sweet collapseable shaft, four tires and wheels(may not be the prettiest wheels but will get it home) too much to even list. Proven winner. It will have a new black body installed next week unless bought before then and then it can be color of choice of buyer. Car can be bought in any stage from bare frame to complete race ready car.
The roller without seat,trans, bellhousing $12,800
The roller without seat,trans,bellhousing, quickchange $11,800
731-695-5461 TJ Herndon
The car has only been run a little over 20 times and has 11 feature wins. The car started out as a Taylor car and before the Texas race I took it to AR and put on the jig and made sure everything was straight. While there I had Landers to put his four bar and pullbar brackets on the car and do some frontend work. Everything on the car was new at the beginning of the year. Has Tilton brake pedals , brand new brake calipers, tiger thermal coated quickchange rearend, BSB birdcages,sweet collapseable shaft, four tires and wheels(may not be the prettiest wheels but will get it home) too much to even list. Proven winner. It will have a new black body installed next week unless bought before then and then it can be color of choice of buyer. Car can be bought in any stage from bare frame to complete race ready car.
The roller without seat,trans, bellhousing $12,800
The roller without seat,trans,bellhousing, quickchange $11,800
731-695-5461 TJ Herndon
dluna11w
New Member
I have an 05 Hoffman with very limited nights on it. (under 60). Sell as a roller or anything in between.
Turnkey would include a 400 sbc in little m dart block fresh sitting in the engine builders shop still. Very nice motor. Also spare 383 motor available. 2 gearte carburators. Falcon tranny, winters bellhousing, reverse starter setup, kse tandem setup, many spare parts...to much to list. Would sell trailer along with it as well.
roller $5000
roller + turnkey with 400 motor, tranny, everything to hit the track $13,500
can give prices of everything else as well if interested.
Don Luna
don@troutjig.com
573-259-1197
Turnkey would include a 400 sbc in little m dart block fresh sitting in the engine builders shop still. Very nice motor. Also spare 383 motor available. 2 gearte carburators. Falcon tranny, winters bellhousing, reverse starter setup, kse tandem setup, many spare parts...to much to list. Would sell trailer along with it as well.
roller $5000
roller + turnkey with 400 motor, tranny, everything to hit the track $13,500
can give prices of everything else as well if interested.
Don Luna
don@troutjig.com
573-259-1197
06 Pierce Modified $5,500 (Please contact me for more pictures)
Would sell with bert transmission, bert bellhousing, and bert starter for another $1,000
Raced 30 laps in 2009
Updated '07/'08 rear stub
Outpace tie rods and trailing arms
Ford 9 inch rear end
hypercoil springs (has newer springs
Hawk Brake Pads
US Brake Calipers
Tubular lower A-Arms
Digital Tach/6 AL Box
Afco shocks
Radiator
620 and 600 gears
lots of spare parts (front/rear bumpers, upper/lower control arms, 2 howe ball joints, 4 replacement ball joint studs, 2 complete tie rods, 2 outpace trailing arms
Also have race motor for sale, if interested.
Please contact Jerry Grither Jr. at 314-707-0479 for any questions.
Would sell with bert transmission, bert bellhousing, and bert starter for another $1,000
Raced 30 laps in 2009
Updated '07/'08 rear stub
Outpace tie rods and trailing arms
Ford 9 inch rear end
hypercoil springs (has newer springs
Hawk Brake Pads
US Brake Calipers
Tubular lower A-Arms
Digital Tach/6 AL Box
Afco shocks
Radiator
620 and 600 gears
lots of spare parts (front/rear bumpers, upper/lower control arms, 2 howe ball joints, 4 replacement ball joint studs, 2 complete tie rods, 2 outpace trailing arms
Also have race motor for sale, if interested.
Please contact Jerry Grither Jr. at 314-707-0479 for any questions.
Attachments
race88
Active Member
Look at my ad
BobPierce turn key operation everything you need
Turn Key Bobpierce racecar operation w/enclos
$30,000.00
2005 Bob Pierce modified complete turn key comes w/ 388 Runion Motor, braswell alcohol carb,brinn tranmission w/bert bellhousing, winters ford 9 inch, spare long block 406 JJR engine....1997 24ft enclosed trailer w/superwinch, tire rack, shock rack, fuel jug holder, electric jack............probaly missing a few items not listed but everything is going........
List of parts that come with car.
1. 8-Afco Spare shocks 2d-1, 1-d, 4d-1, bp-0, bp7”-3d, bp7”-3d, bp9”-3d, bp-4d
2. Shocks on car are bp-4d, bp-4d-1,bp-2d-1,bp-2d
3. 8-2” offset wheels,4-2” beadlocks, 1-3” beadlock
4. 17 Tires -3 tires are brand new
5. 50 gal methanol w/manual pump
6. 3- fuel jugs
7. lug wrench, rivet gun, tire siper,beadbreaker,
8. 3-spare upper a-arms, 2-spare tubular lower a-arms
9. 1-set of spare –link and 4 link bars w/heims
10. Set of Intercomp electronic scales
11. 2-sets of spare spindles
12. 3-sets of gears w/ totes 5.67, 6.00, 6.50
13. Spare front and rear bumper
14. Spare set of balljoints
15. Set of spare rotors
16. 3- spare brake calipers
17. 6-Spare springs
18. 1-Spare driveshaft
19. 150# lead
On the car now
Prc aluminum radiator
Krc aluminum Power steering pump
Schoenefeld Ceramic coated headers
New in 08, 6th coil assembly
New in 08, pull bar and spring
Braswell alcohol carb w/ BG bypass
Brinn Aluminum tranny
Bert bellhousing
Rear Drive starter
Southwest speed driveshaft
__________________
Ready to get everything going again
BobPierce turn key operation everything you need
Turn Key Bobpierce racecar operation w/enclos
$30,000.00
2005 Bob Pierce modified complete turn key comes w/ 388 Runion Motor, braswell alcohol carb,brinn tranmission w/bert bellhousing, winters ford 9 inch, spare long block 406 JJR engine....1997 24ft enclosed trailer w/superwinch, tire rack, shock rack, fuel jug holder, electric jack............probaly missing a few items not listed but everything is going........
List of parts that come with car.
1. 8-Afco Spare shocks 2d-1, 1-d, 4d-1, bp-0, bp7”-3d, bp7”-3d, bp9”-3d, bp-4d
2. Shocks on car are bp-4d, bp-4d-1,bp-2d-1,bp-2d
3. 8-2” offset wheels,4-2” beadlocks, 1-3” beadlock
4. 17 Tires -3 tires are brand new
5. 50 gal methanol w/manual pump
6. 3- fuel jugs
7. lug wrench, rivet gun, tire siper,beadbreaker,
8. 3-spare upper a-arms, 2-spare tubular lower a-arms
9. 1-set of spare –link and 4 link bars w/heims
10. Set of Intercomp electronic scales
11. 2-sets of spare spindles
12. 3-sets of gears w/ totes 5.67, 6.00, 6.50
13. Spare front and rear bumper
14. Spare set of balljoints
15. Set of spare rotors
16. 3- spare brake calipers
17. 6-Spare springs
18. 1-Spare driveshaft
19. 150# lead
On the car now
Prc aluminum radiator
Krc aluminum Power steering pump
Schoenefeld Ceramic coated headers
New in 08, 6th coil assembly
New in 08, pull bar and spring
Braswell alcohol carb w/ BG bypass
Brinn Aluminum tranny
Bert bellhousing
Rear Drive starter
Southwest speed driveshaft
__________________
Ready to get everything going again
Still looking?
I have 2 modifieds for sale
1998 RaceMart Raider turnkey with 406sbc listed in this forum
2004 Starterson Turnkey with 355sbc also listed in this forum.
all of these are very competitive cars and built with the best of everything. Feel free to give me a call @ 573-489-0165. These cars are located in Columbia,MO.
I have 2 modifieds for sale
1998 RaceMart Raider turnkey with 406sbc listed in this forum
2004 Starterson Turnkey with 355sbc also listed in this forum.
all of these are very competitive cars and built with the best of everything. Feel free to give me a call @ 573-489-0165. These cars are located in Columbia,MO.
2007 Pierce Mod Roller less motor and trans Seat #551 5 feature wins QC Qa1 Willwood KRC Autometer Afco $7100 call 217-228-0621 or E-mail dlonj35@yahoo.com for pics Hank
10X motorsports
Member
Look at the 06 skyrocked ad
06 skyrocket complete roller completely updated this year $8500
06 skyrocket complete roller completely updated this year $8500
RBIRacing
Buff
I have older Harris chassis with 355 sbc we run as a B mod. Like to get $4800.00 turn key and $2000.00 roller 314 280-1163 Bob or buffster8@aol.com I have it posted in the modified classifieds. Under older Harris modified also pic there too. There are a few in my profile
dirtracn14
Unregular User
2008 Pierce Mod--$6000.00
Car has clamped up left side screw jack plate, right side spring in front option on coil over, and also spring on top with jack bolt. best of both if you choose.
Teardrop Fuel cell
Complete car-------- Less Seat and Msd, Tach
Wilwood Pedals
Winters Mag Quick Change
Nova Tubular lowers
Lightweight mid motor plate
Pierce Uppers
2 race Old Afco Radiator
R/F Shutoff
Shifters and linkage
Master Disconnect Switch
Hypercoil Springs
Integra Shocks
Aero wheels
Impact Belts
Safety steering wheel from speedway, no holes
2 inch BSI Drive shaft
Extras posted here: PARTS OUTSIDE OF ROLLER- 2 new lowers , 1 new upper, 8 wheels and tires, total 12 in all, 5 extra springs , 2 spring cups, 2 beadlock rings, set of schonfield headers fits 23 degree chevy like new, 2 more good tires, Power steering box, and another afco radiator, and a spare spindle
Here is original post dropped price for this week:
2008 Pierce Mod#663 n For Sale or trade For Rocket - STLRacing.com
815-295-3316
Car has clamped up left side screw jack plate, right side spring in front option on coil over, and also spring on top with jack bolt. best of both if you choose.
Teardrop Fuel cell
Complete car-------- Less Seat and Msd, Tach
Wilwood Pedals
Winters Mag Quick Change
Nova Tubular lowers
Lightweight mid motor plate
Pierce Uppers
2 race Old Afco Radiator
R/F Shutoff
Shifters and linkage
Master Disconnect Switch
Hypercoil Springs
Integra Shocks
Aero wheels
Impact Belts
Safety steering wheel from speedway, no holes
2 inch BSI Drive shaft
Extras posted here: PARTS OUTSIDE OF ROLLER- 2 new lowers , 1 new upper, 8 wheels and tires, total 12 in all, 5 extra springs , 2 spring cups, 2 beadlock rings, set of schonfield headers fits 23 degree chevy like new, 2 more good tires, Power steering box, and another afco radiator, and a spare spindle
Here is original post dropped price for this week:
2008 Pierce Mod#663 n For Sale or trade For Rocket - STLRacing.com
815-295-3316
circle dirt
Member
2008 Mach 1
2008 Mach 1 complete minus engine.4 bar ,bsb cages,afco bushing pull rod, New deck and body , black on black. 16 nights on car 4 feature wins , 7 heats. Quick change,fast shaft, bert ball spline, wilwood calipers ,fresh air system,32 gallon cell, new Kirkey seat, simpson belts,wilwood composite pedals,MSD,shifters,everything you need minus only the engine. $ 8500.00
www.coxracing.zoomshare.com for pictures
2008 Mach 1 complete minus engine.4 bar ,bsb cages,afco bushing pull rod, New deck and body , black on black. 16 nights on car 4 feature wins , 7 heats. Quick change,fast shaft, bert ball spline, wilwood calipers ,fresh air system,32 gallon cell, new Kirkey seat, simpson belts,wilwood composite pedals,MSD,shifters,everything you need minus only the engine. $ 8500.00
www.coxracing.zoomshare.com for pictures
