Flyin Pile
Jerk to the 5th Power
More stuff added and some prices lowered
---1998 Chubbie Chassis, never bent. not a roller!! comes with lower control arms, weight jacks on all 4 corners, front springs, rear springs, headers, driveshaft, some gauges, clutch pedal and mc, brake pedal and mc, 18 gal fuel cell,aluminum motor plate, black decking SOLD
---350 4 bolt main block .060 over, race prepped, 461 heads mild port work 2.08 1.60 stainless valves, roller rockers, guide plates, stud girdle, head studs, Scat 9000 400 crank, 6" Scat rods, KB pistons (.150 dome), Lunati roller cam (over .600 lift), Schoenfeld headers, aluminum water pump, aluminum intake (gasket matched to heads), 8 qt oil pan. Fresh with 0 laps (LZR freshened the short block) $4500.
---Holley 500 2bbl (C&S worked it over), $150. SOLD
---4 Powerglide transmissions, 2 complete, 2 in pieces, extra gasket sets and friction disks, 2 direct drive flanges and hubs $450. $425.
---Ford 9" center, 6:20 gear set, mini spool, 28 spline SOLD
--- 1 brass radiators both $30.
---MSD 6AL ignition box SOLD
---Nice open trailer, has 8 tie down hooks, hidden ramp storage, 30"X35" box lockable with doors on both sides, 3500lb winch, battery, battery box, tire rack.good spare tire,4 Brand new tires, just serviced the bearings and seals. 14' deck w/4' dove tail, 76" between the wheelwells. $XXXX. SOLD
---4400 watt generator runs good SOLD
---Th400 transmission out of 90 chevy truck about 80K miles $75. obo
--- Th700R4 transmission, 22xxx miles SOLD
---S10 5 speed manual transmission $50. obo
---19 e-mods 3 beadlock rims and 10 non bead lock rims for couple of these tires only have hot laps on themall for SOLD
--- some stock heads off a 327 $40 obo
--- aluminum case for gm 4 speed $30. obo
--- aluminum bell housing (stock) I have 2 $25 ea or $40. for both
--- 3 speed manual w/shifter $100.
---Ford 9" w/28 spline axles (no gear), has rear disk brakes and calipers,center pull bar SOLD
--- panhard bar SOLD
--- fuel cell 18 gallon in a can SOLD
--- motor plate, aluminum SOLD
--- metric spindles, with a caliper and rotors 1 left 1 right, both SOLD
--- tube upper A arms with balljoints both for SOLD
--- 461 heads SS valves 2.08 and 1.60 screw in studs and guide plates big roller springsSOLD
I'll start pullin parts off tomarrow, so pm me or e-mail me if there is something you want or need. I'm open to serious offers too. I can post pictures too.
master_cheater@4m.net
---1998 Chubbie Chassis, never bent. not a roller!! comes with lower control arms, weight jacks on all 4 corners, front springs, rear springs, headers, driveshaft, some gauges, clutch pedal and mc, brake pedal and mc, 18 gal fuel cell,aluminum motor plate, black decking SOLD
---350 4 bolt main block .060 over, race prepped, 461 heads mild port work 2.08 1.60 stainless valves, roller rockers, guide plates, stud girdle, head studs, Scat 9000 400 crank, 6" Scat rods, KB pistons (.150 dome), Lunati roller cam (over .600 lift), Schoenfeld headers, aluminum water pump, aluminum intake (gasket matched to heads), 8 qt oil pan. Fresh with 0 laps (LZR freshened the short block) $4500.
---Holley 500 2bbl (C&S worked it over), $150. SOLD
---4 Powerglide transmissions, 2 complete, 2 in pieces, extra gasket sets and friction disks, 2 direct drive flanges and hubs $450. $425.
---Ford 9" center, 6:20 gear set, mini spool, 28 spline SOLD
--- 1 brass radiators both $30.
---MSD 6AL ignition box SOLD
---Nice open trailer, has 8 tie down hooks, hidden ramp storage, 30"X35" box lockable with doors on both sides, 3500lb winch, battery, battery box, tire rack.good spare tire,4 Brand new tires, just serviced the bearings and seals. 14' deck w/4' dove tail, 76" between the wheelwells. $XXXX. SOLD
---4400 watt generator runs good SOLD
---Th400 transmission out of 90 chevy truck about 80K miles $75. obo
--- Th700R4 transmission, 22xxx miles SOLD
---S10 5 speed manual transmission $50. obo
---19 e-mods 3 beadlock rims and 10 non bead lock rims for couple of these tires only have hot laps on themall for SOLD
--- some stock heads off a 327 $40 obo
--- aluminum case for gm 4 speed $30. obo
--- aluminum bell housing (stock) I have 2 $25 ea or $40. for both
--- 3 speed manual w/shifter $100.
---Ford 9" w/28 spline axles (no gear), has rear disk brakes and calipers,center pull bar SOLD
--- panhard bar SOLD
--- fuel cell 18 gallon in a can SOLD
--- motor plate, aluminum SOLD
--- metric spindles, with a caliper and rotors 1 left 1 right, both SOLD
--- tube upper A arms with balljoints both for SOLD
--- 461 heads SS valves 2.08 and 1.60 screw in studs and guide plates big roller springsSOLD
I'll start pullin parts off tomarrow, so pm me or e-mail me if there is something you want or need. I'm open to serious offers too. I can post pictures too.
master_cheater@4m.net
