Special Payout for Hornets/Wannabees this Sunday at Fredericktown

Millsey

Millsey

New Member
With the tremendously appreciated $500 donation to the Fredericktown Raceway Azalea Racefest this next SUNDAY, JUNE 1st, our revised pay scale will look something like this. What I simply did was take the $500 and equally split it into the top 20 positions. That means if you make the 20-vehcile feature you will get no less than $45.

Hornets/Wannabees
15-lap feature
Payout
1st - $175
2nd - $125
3rd - $105
4th - $95
5th - $85
6th - $75
7th - $65
8th - $55
9th - $50
10-20th - $45

Gates open at 3 p.m. with racing around 4:30!!

Don't you think that seems to be the fairest!! REMEMBER, there MUST BE AT LEAST 16 cars to recieve this purse. If not it will be reduced..

For more information on this event contact me at (573) 747-0566.
 
Rules for this coming Sunday

1. Any 4-cylinder car with a maximum wheelbase of 1 04" and a complete stock body, frame and suspension. No bracing anywhere except inside the drivers compartment. Dash, steering and pedals must remain stock for that make and model. All insulation under hood must be removed.

2. Stock carburetor I fuel injection, with stock OEM air intake / filter system for that make and model. No turbo chargers.

3. Stock transmission for that make and model.

4. Battery must remain under the hood in stock, secure location.

5. Stock unaltered rear end for that make and model.

6. Passenger tires, 70 series or taller only. Wheels and tires must be same size on all four corners. 45 lbs. Air pressure minimum at all times, all four comers. No racing wheels.

7. If stock gas tank is ahead of rear axle it may remain in place. If stock gas tank is behind rear axle it must be replaced with a fuel cell or 6.6 gallon maximum boat tank. Fuel cell / boat tanks must be covered secured and located in trunk.

8. ROLL CAGE: A full four point, box type roll cage is mandatory. Roll cage must be securely welded to either 1/8" plates measuring 4'tx8" or to 1/8" angle stock material welded to rocker panel area. Tubing must be a minimum of 1.5" in diameter and .095 wall thickness. Door bars required on drivers' side. No galvanized, black gas or aluminum tubing allowed. Roll cages will be inspected. Roll bars within driver area must be padded. Approved window net on driver side, must be quick release, rectangular type.

9. Drivers doors must be welded or chained shut. Driver side doorplates recommended.

10. Approved aluminum racing seat mandatory. Seat must be secured to cage assembly using four (4) grade eight bolts with lock nuts, no less than three eighths (3/8) inch diameter.

11. Five point, three inch approved safety harness mandatory. Manufacturers date tag must show I /99 or newer. If date tag is not present, belts must be replaced. Belts must be secured to cage assembly using one half(1/2) inch diameter grade eight bolts and lock nuts.

12. Approved helmet, fire suit and gloves required.

13. All glass must be removed. Windshield must be replaced with heavy wire screen. Three 3/8" horizontal bars to be securely welded in front of driver.

14. Third brake light must remain intact and operable. Car horn must work. .

15. Management claim in affect at all times. Claim amount $500.00. Does not include fuel cell or safety equipment.

16. All cars are subject to a minimum specification inspection at any time. It is the responsibility of the driver to prepare their car free of defects and in a safe racing condition.

17. Minimum age 16 and must possess a state driver license.

18. All cars and drivers must register and have number approved before allowed to race. NO EXCEPTIONS.

19. Cars must be painted. Car number must be at least 24” tall and be in a legible contrasting color on doors, and car number at least 6" tall on upper corner of passenger side of windshield. No duplicate numbers. Cars not properly painted will start in the back of each race.
 
You must log in or register to reply here.




Back
Top