i have an 09 port city. it is the new style with the down bars going to front of snouts. very good car. won the last race it raced and the last race at monroe speedway in louisiana. the car was setup by Deon's Race cars. a very well known guy that has been in ASA racing for a long time. it...
i have an 09 port city. it is the new style with the down bars going to front of snouts. very good car. won the last race it raced and the last race at monroe speedway in louisiana. the car was setup by Deon's Race cars. a very well known guy that has been in ASA racing for a long time. it has a...
This is a project truck that only needs a little more work to be finished, and started to be put back together.
What I have done to the truck so far:
1. replace front/rear cab supports
2. replaced cab corners
3. replaced rocker panels
4. filled heater holes on firewall
5. filled gas tank hole...
I have a 360 CI SBC motor for sale.
I built this motor to run as a B-Mod, but it could be used in other classes as well or street/strip.
It is a .060 over bore chevy block. the block has been decked, line bored, lifter valley has been polished, and has lifter valley vents.
It has a 46 lb...
I have a 360 CI SBC motor for sale.
I built this motor to run as a B-Mod, but it could be used in other classes as well or street/strip.
It is a .060 over bore chevy block. the block has been decked, line bored, lifter valley has been polished, and has lifter valley vents.
It has a 46 lb...
i have a 9" 5.43 gear for sale.
31 spline with mini spool. only 3 races on it.
$200
Set of straight out modified headers. only 2 races since new.
$80
Aluminum reduction pulleys, with belts.
$50
Pull bar with 750 Spring. needs 1 heim. not sure on length. will measure and post
$40
solid pull...
We have a 1966 Chevy SWB Truck - Project we need to sell.
It has a clean title. the truck is disassembled, because i started to restore but now have to sell because of funds and now we don't have time to work on it.
the frame has been sand blasted and painted black. it has a custom drive...
I have a 360 CI SBC motor for sale.
I built this motor to run as a B-Mod, but it could be used in other classes as well or street/strip.
It is a .060 over bore chevy block. the block has been decked, line bored, lifter valley has been polished, and has lifter valley vents.
It has a 46 lb...
I have a 360 CI SBC motor for sale.
I built this motor to run as a B-Mod, but it could be used in other classes as well or street/strip.
It is a .060 over bore chevy block. the block has been decked, line bored, lifter valley has been polished, and has lifter valley vents.
It has a 46 lb...
i have a 16 foot H&H trailer for sale. it is heavy duty but is fairly light. has pull out side ramps, winch. i pulled my racecar with it but could be used for anything. it is 82 1/2 inches inbetween fenders. has fairly new trailer tires on it.
no title, but all you will have to do is go to...
i have a 16 foot H&H trailer for sale. it is heavy duty but is fairly light. has pull out side ramps, winch. i pulled my racecar with it but could be used for anything. it is 82 1/2 inches inbetween fenders. has fairly new trailer tires on it.
no title, but all you will have to do is go to...
I have a 360 CI SBC motor for sale.
I built this motor to run as a B-Mod, but it could be used in other classes as well or street/strip. This motor is ready to drop in and go. just needs starter
It is a .060 over bore chevy block. the block has been decked, line bored, lifter valley has been...
I have a 360 CI SBC motor for sale.
I built this motor to run as a B-Mod, but it could be used in other classes as well or street/strip. This motor is ready to drop in and go. just needs starter
It is a .060 over bore chevy block. the block has been decked, line bored, lifter valley has been...
355 short block: 12.5:1 keithblack pistons, x-rods, stock forged crank. it is an 010 block.
Needs rings and bearings. it is disassembled. $500 obo.
500 cfm 4412 holley carb. used on dirt and asphalt modified. it is legal, runs great. $175 with adaptor plate.
6 - keith black silvolite, flat top...
355 short block: 12.5:1 keithblack pistons, x-rods, stock forged crank. it is an 010 block.
Needs rings and bearings. it is disassembled. $500 obo.
500 cfm 4412 holley carb. used on dirt and asphalt modified. it is legal, runs great. $175 with adaptor plate.
6 - keith black silvolite, flat top...
355 short block: 12.5:1 keithblack pistons, x-rods, stock forged crank. it is an 010 block.
Needs rings and bearings. it is disassembled. $500 obo.
500 cfm 4412 holley carb. used on dirt and asphalt modified. it is legal, runs great. $175 with adaptor plate.
6 - keith black silvolite, flat top...
Speedway torque arm. brand new, w/ stabilizer bar and heims. $90
60 inch Floater Rearend - complete from hub to hub. has 2 - link mounts welded to it and caliper mounts, top link mount.
it is a centered housing. $500
Bert transmission. new style with blue side plate. 0 lapes since being...
Speedway torque arm. brand new, w/ stabilizer bar and heims. $90
60 inch Floater Rearend - complete from hub to hub. has 2 - link mounts welded to it and caliper mounts, top link mount.
it is a centered housing. $500
Bert transmission. new style with blue side plate. 0 lapes since being...