Search results

Looking for 60" floater housing with or without brackets, metric brackets preferred but not necessary. Thanks, Greg

sold sold sold

1995 Saturn sl2, one owner, has title, w/5spd trans, dohc motor, ran fine, now needs motor. Everything else in good shape. Great for race car $500 obo Call 314 638 2300 8-5 m-f not on here much, please call

sold sold sold

2007 Impressive mod #259 Impressive chassisSTILL HAVE MID PLATE AND BELLHOUSING $1200 OBO New floater w/new axlesSOLD New BSB birdcagesSOLD New rear hubsSOLD New Bilstein shocksSOLD New Afco springsSOLD New swedge tubes and heimsSOLD New headersSOLD New radiatorSOLD pull bar (not new, but spring...

I've got a rochester 2gc 2bbl carb dripping from the rt side booster at idle. When I ran it last, the rt side header was glowing. I took it apart, found that the left side emulsion tube had fallen out of the booster assy, and the air horn (top) gasket had shriveled up. I fixed the emulsion tube...

5 on 5 8" wheels, 2 chrome one is 1" one is2" also have one silver 1" wheel USED--- have a few dings, but still usable.$20 ea OBO or could use a couple e mod A's call Greg 636-282-8512

80 360 dodge truck motor, has block, heads, timing cover, valve covers, and oil pan. needs rebuilt, it's tired and cam is worn out. make offer 636-282-8512 Thanks, Greg

Sold sold sold!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Would like to trade 6.00 gear for 1.84 trans (2 lines on input shaft), or 4.10 gear 28 spline PM or call 636-282-8512 Thanks, Greg

Who in the area can cut splines on a shortened 9" axle? Thanks, Greg

1 air cooled powerglide case(core), 1 powerglide with broken case (about 20 nights) with manual valve body, 2 torque converters, Box of misc parts for pg, another man valve body,pumps couple tail shaft hsgs, B&M deep alum pan, Hurst pro stick for pg, needs cable,etc. TIRED OF TRIPPING OVER THIS...

I have a 1 ton ford service van. It is white, and has already got a ladder rack, shelves, and bulkhead. $1250 or best reasonable offer. Great for paper delivery, painter, plumber, electrician,etc. Needs to go soon... Give me a call if interested 636-282-8512 thanks, Greg

I've got a 90 chev tk motor I put a carb on and have a strange noise coming from exhaust on rt side. The only place you hear the crackle or popping noise is out the rt side tail pipe. No noise under hood,(ex leak,or mechanical noise) only does it under load,Idles perfectly smooth, and doesn't...

95 quad 4 dohc 5 speed grand am,140,000 mi. black,body and int ok shape,runs, needs head gasket and alignment. It does have a new clutch, clutch master cyl, and clutch slave cyl, new starter......kinda quick little car (hornet or rollover candidate?) $300 obo Call Greg, 636-282-8512 after 6pm

I have a used alum seat w/blue cloth cover (kinda rough, but usable) $30.00 call Greg 636-282-8512 after 6pm thanks

I have 2 torque converters, 1 good air cooled p/g case, 1 broken p/g case w/all internals and manual valve body, and another set of internals, including another man valve body, B&M deep aluminum pan, and hurst pro stick with alum cover for p/g (needs a cable) $100 OBO Also have 1/4 inch homade...

02 focus 1.9 single cam has head, but bad. short block is good(still has hone marks in cyls) replaced engine and still have old one. has around 70,000 miles also have starter. $100 OBO pm or call 636-282-8512 SOLD SOLD SOLD

I have a set of comp cams 1.52 roller rockers with 7/16 studs and locks came out of a SBC motor w/only a couple of nights on it $150.00 OBO Call 636-282-8512 or pm here. Thanks, Greg

I need a steel bellhousing and flywheel, prefferably 168 tooth, 153 tooth may also work. msg here, or call 636-282-8512 Thank You, Greg